(Your shopping cart is empty)

  Home > Optics > Acousto-optic Devices and Electro-optic Devices > Acoustic-optic Modulators (AOM) and AOM Drivers >

131268: AO Q-switch Drivers (low power, high speed, compact Q-switch Driver, 2-24W)
Q-switch Drivers (low power, high speed, compact Q-switch Driver, 2-24W)


 
A compact high power RF driver module is available in output powers of 50 or 100W. Powered from 28vDC,
the modulation inputs allow either full digital control or activation of an internal pulse generator.
First pulse suppression is implemented through either analogue modulation, RF off analogue control,
triggered first pulse suppression, or triggered pre-pulse kill, as described in our FPS guidance notes.
On board LED's and TTL logic outputs monitor driver status and cooling is through forced air over the
heat sink.

Parameter Specification
Output Frequency: XX=24,27, or 41, Where RF Frequency=24.00, 27.12, 40.68 MHz0.01%
Spurious Levels: -50 dBc Maximum
Harmonic Distortion -20 dB Maximum
Modulation Input
Mod In Fixed (pin 3) TTL Levels Triggered on TTL Rising Edge. Pulse Width Applied >50ns.
Mod In Variable (ping 5) TTL Levels TTL High=RF Off
Extinction Ratio: 40dB Minimum
RF Rise Time 10% to 90% 100ns Maximum
RF Fall Time: 90% to 10% 50 ns Maximum
Modulation Repetition Rates: 1 Hz to 500kHz for Fixed Modulation
DC to 500kHz for Variable Modulation
Fixed Modulation Output Pulse Width 1 to 20s, Customer Adjustable
Adjustable Range:
Available Pulse Suppression Modes: zzz=Mode
Modulation Operating Mode is "Factory FPS=First Pulse Suppression
Set" Internally. PPK=Pre PUlse Kill
R05=RF Switched to Analog Control
A05=Analog Control
FPS Trigger(pin 2) for Pulse Suppression TTL Levels, Triggered on TTL Rising Edge
for Units Configured with FPS, PPK:
Analog in (pin 6) for Power Control 0 to 5 volts Analog
for Units Configured with A05, R05
Enable-Stand by Mode (pin 11) >3watt dissipation in stand by mode.
TTL High or no connection = Normal operation
TTL Low=Stand by Mode
Momentary TTL Low=Driver Reset-after fault is removed.
Zero Crossing Enable(pin 7) noramally: TTL high or no connection-disabled, TTL low-enabled
  TTL high or no connection-enabled, TTL low-disabled
Sync out (pin 1) Outputs 3.3 volt signal
RF Power Output: YY watts where YY=2 to 24 watts
Output Impedance: 50Ω
Supply Voltage: +15VDC
Supply Current: <3 amps.
OPERATING TEMPERATURE: +10 to +55C case Temperature
Contact Cooled The Driver must be attached to a heatsink capable of dissipating 25 watts
MAXIMUM RATINGS:
Supply Voltage: +18volts
Power Output: No DC Feedback Allowed
Storage Temperature: -20 to + 85C
Dimesion 90x60x25mm


Item# Item Name Send Me a Quote Qty Add
131269 131269: First Pulse Suppression 2-24W 24MHZ Q-switch
$0.00
131270 131270: RF Off Analogue Control 2-24W 24MHZ Q-switch
$0.00
131271 131271: Triggered Pre-Pulse Kill 2-24W 24MHZ Q-switch
$0.00
131272 131272: Analogue Modulation 0-5V 2-24W 24MHZ Q-switch
$0.00
131273 131273: First Pulse Suppression 2-24W 27MHZ Q-switch
$0.00
131274 131274: RF Off Analogue Control 2-24W 27MHZ Q-switch
$0.00
131275 131275: Triggered Pre-Pulse Kill 2-24W 27MHZ Q-switch
$0.00
131276 131276: Analogue Modulation 0-5V 2-24W 27MHZ Q-switch
$0.00
131277 131277: First Pulse Suppression 2-24W 41MHZ Q-switch
$0.00
131278 131278: RF Off Analogue Control 2-24W 41MHZ Q-switch
$0.00
131279 131279: Triggered Pre-Pulse Kill 2-24W 41MHZ Q-switch
$0.00
131280 131280: Analogue Modulation 0-5V 2-24W 41MHZ Q-switch
$0.00
Check the items you wish to purchase, then click

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Optics > Acousto-optic Devices and Electro-optic Devices > Acoustic-optic Modulators (AOM) and AOM Drivers
Optics > Acousto-optic Devices and Electro-optic Devices > Q switches and drivers
Optics > Acousto-optic Devices and Electro-optic Devices
 About Us
 Become an Affiliate
 Privacy Policy
 Send Us Feedback
 
Company Info | Advertising | Product Index | Category Index | Help | Terms of Use
Copyright © Produstrial. All Rights Reserved.
Built with Volusion